Вы здесь

P0107 P0108

DTC    P0107    Manifold Absolute Pressure / Barometric Pressure Circuit Low Input

DTC    P0108    Manifold Absolute Pressure / Barometric Pressure Circuit High Input


 

DESCRIPTION

The manifold absolute pressure sensor detects pressure inside the intake manifold as an absolute pressure with a built-in sensor and outputs a voltage. Based on the voltage from the vacuum sensor, the ECM controls the air fuel ratio and corrects any errors in the pressure sensor due to changes in pressure.
P0107 P0108 / Lexus CT200h / ZWA10
 

DTC No. DTC Detecting Condition Trouble Area
P0107 The output voltage from the manifold absolute pressure sensor below 0.5 V for 0.5 seconds (1 trip detection logic).
  1. Open or short in manifold absolute pressure sensor circuit
  2. Manifold absolute pressure sensor
  3. ECM
P0108 The output voltage from the manifold absolute pressure sensor higher than 4.5 V for 0.5 seconds (1 trip detection logic).
  1. Open or short in manifold absolute pressure sensor circuit
  2. Manifold absolute pressure sensor
  3. ECM

HINT:

When DTC P0107 or P0108 is detected, check the manifold absolute pressure by selecting Powertrain / Engine and ECT / Data List / MAP on the intelligent tester.

 

 

Manifold Absolute Pressure (kPa) Malfunction
Approximately 0 kPa
  1. Short in PIM circuit to ground
  2. Short in PIM circuit to E2 circuit
130 kPa or higher
  1. Open in VC circuit or short in VC circuit to PIM circuit
  2. Open in PIM circuit
  3. Open in E2 circuit


 

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the manifold absolute pressure. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the manifold absolute pressure sensor and sets a DTC.
Example:
When the sensor output voltage remains below 0.5 V, or higher than 4.5 V for 0.5 seconds, the ECM sets a DTC.
 

MONITOR STRATEGY

 

Frequency of Operation Continuous

 

CONFIRMATION DRIVING PATTERN

  1. Put the engine in inspection mode (maintenance mode).
  2. Start the engine and wait for 5 seconds or more.

WIRING DIAGRAM


P0107 P0108 / Lexus CT200h / ZWA10


 

INSPECTION PROCEDURE

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.READ VALUE USING INTELLIGENT TESTER (MAP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.

  1. Read the MAP value.

    OK:

    Same value as the actual atmospheric pressure.

     

    HINT:

  1. Standard atmospheric pressure is 101 kPa (758 mmHg). For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). The pressure also varies due to the weather (high atmospheric pressure, low atmospheric pressure).
  2. Also, check "Atmosphere Pressure" in the Data List.

 

 

  NG
Go to step 2
 
OK  
 
CHECK FOR INTERMITTENT PROBLEMS 

 

2.CHECK TERMINAL VOLTAGE (MANIFOLD ABSOLUTE PRESSURE SENSOR)


 

P0107 P0108 / Lexus CT200h / ZWA10
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection Switch Condition Specified Condition
    D3-3 (VC) - D3-2 (E2) Power switch on (IG) 4.5 to 5.5 V
    D3-1 (PIM) - D3-2 (E2) Power switch on (IG) 3.0 to 5.0 V
    Text in Illustration 
    *a Front view of wire harness connector
    (to Manifold Absolute Pressure Sensor)
    Result 
    Result Proceed to
    Outside standard range A
    Within standard range B

     

 

  B
Go to step 4
 
A  
 

 

3.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.
     

    Standard Resistance:

     
    Tester Connection Condition Specified Condition
    D3-3 (VC) - D27-72 (VCPM) Always Below 1 Ω
    D3-2 (E2) - D27-71 (EPIM) Always Below 1 Ω
    D3-1 (PIM) - D27-69 (PIM) Always Below 1 Ω
    D3-3 (VC) or D27-72 (VCPM) - Body ground Always 10 kΩ or higher
    D3-1 (PIM) or D27-69 (PIM) - Body ground Always 10 kΩ or higher
  NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
 
OK  
 
REPLACE ECM

 

4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Replace the manifold absolute pressure sensor.

NEXT  
 

 

5.CHECK WHETHER DTC OUTPUT RECURS (P0107 OR P0108)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG) and turn the tester on.

  1. Clear the DTCs.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result Proceed to
    DTC is not output A
    DTC P0107 or P0108 is output B
  B
REPLACE ECM
 
A  
 
END